SPONSOR ADS

  HOMEPAGE

  Parents2be.info

 

DIRECTORY CATEGORIES

101 Parenting
Active Parenting
Adult Child Parenting
Article Parenting
Article Parenting Single
Attachment Parenting
Authoritarian Parenting
Bad Parenting
Biblical Parenting
Boards Message Parenting
Book Parenting
Center Parenting
Chat Parenting Room
Child Parenting
Class Florida Parenting
Class Free Parenting
Class Online Parenting
Class Parenting
Deference Parenting Patient
Different Parenting Style
Discipline Parenting
Divorce Parenting
Education Parenting
Effective Parenting Systematic Training
Family Parenting
Florida Magazine Parenting South
Forum Parenting
Foster Parenting
Free Magazine Parenting
Gay Parenting
Good Parenting
Group Parenting
Group Parenting Support
Help Parenting
Homosexual Parenting
India Parenting
Information Parenting
Issue Parenting
Kid Parenting
Lesbian Parenting
Magazine Online Parenting
Magazine Parenting
New Parenting Program York
Pagan Parenting
Parenting Plan
Parenting Planned
Parenting Poem
Parenting Shared
Parenting Single
Parenting Site
Parenting Site Web
Parenting Spiritual
Parenting Stress
Parenting Style
Parenting Surrogate
Parenting Technique
Parenting Teen
Parenting Teenage
Parenting Time
Parenting Tip

 

SPONSOR ADS

SPONSOR ADS

How to Make Camping Shoot-the-Chute

By David Z

Shoot-the-Chute

A "Shoot-the-Chute" is great fun and one should be built in every camp visit and "Swimming Hole." The one described below has stood the test of several years in many different camp sites.

The plan drawn is for a chute 40 feet long, 3 feet wide and 18 feet high. These dimensions can be changed in length and height, but not in width.

The chute is built of 7/8-inch matched pine boards, to the same width as sheet zinc, usually 3 feet; the boards being firmly cleated together on the under side by 2 x 6-inch cleats 5 feet apart, throughout the length of the chute.

Boards should be screwed to the cleats from the face of the chute with 1-1/2-inch screws, the heads being counter sunk.

The several lengths of zinc are soldered into one piece, the joints being on the under side (as shingles on a roof) fastened to the boards with 8-oz. tacks; set in from the edge about 1 inch and about 6 inches apart.

The side strips of maple (soft wood will not do on account of the danger of splintering) 2 inches wide and 3 inches high, rounded slightly on upper edge, are placed directly over the edge of the zinc and covering the tacks.

Screw the strips firmly to the chute with 2-inch screws from the under side. These ought to be placed not more than 2 feet apart. Probably each will have two or more strips in making a piece of sufficient length. If so, care should be taken to have the pieces joined on a bevel with a slant from outer edge toward bottom of chute, so as to leave no edge.

The utmost care should be used to have a perfectly smooth surface on the inside of the chute. A pump or bucket is needed at the top of the chute to wet the surface before the swimmer starts his slide.

The supports should be firmly braced with 2 x 4-inch timber, and lower end of chute should extend over the pier at least 1 foot and not nearer the surface of the water than 3 feet perpendicularly, allowing the swimmer to enter the water as in a dive.

The chute can be fastened to the supporting braces through timbers, into maple side strips with a good heavy log screw. A platform 3 feet wide and 4 feet long near the top of chute, and set just waist deep from the top of chute will make starting easy.


About the author:
Welcome to allcampings.com ( http://www.allcampings.com), the Best Outdoor Action Guide about camping. Information on trip planning, clothing, travel, other camping skills, and much more...



Circulated by Article Emporium




 




  © Copyright 2011. All Rights Reserved.